LHEF for Matching

From Wiki Les Houches 09

(Difference between revisions)
Jump to: navigation, search
Line 11: Line 11:
The standards are found here:
The standards are found here:
-
* [http://arxiv.org/pdf/hep-ph/0609017 A standard format for Les Houches event files, hep-ph/0609017]
+
* [http://arxiv.org/pdf/hep-ph/0609017 A standard format for Les Houches event files, hep-ph/0609017]
-
* [http://arxiv.org/pdf/hep-ph/0109068 Generic User Process Interface for Event Generators, hep-ph/0109068]
+
* [http://arxiv.org/pdf/hep-ph/0109068 Generic User Process Interface for Event Generators, hep-ph/0109068]
As the matching and merging of tree-level matrix elements and parton
As the matching and merging of tree-level matrix elements and parton
Line 77: Line 77:
  * "ETmiss" the sum of the pt of the neutrinos in the process
  * "ETmiss" the sum of the pt of the neutrinos in the process
  * ...
  * ...
-
* p1 (D=any): The particle for which this cut applies. This can either
+
* p1 (D=any): The particle for which this cut applies. This can either be a number corresponding to a given particle PDG code or one of the following
-
be a number corresponding to a given particle id code or
+
-
one of the following
+
  * "any" any particle
  * "any" any particle
  * "jet" any coloured particle
  * "jet" any coloured particle
Line 85: Line 83:
  * "guds" ("gudsc") any light quark or gluon
  * "guds" ("gudsc") any light quark or gluon
  * "b" ("c") any b or bbar (c or cbar) quark
  * "b" ("c") any b or bbar (c or cbar) quark
-
  * "l" ("l+" or "l-") any (positively or negatively) charged lepton       ...
+
  * "l" ("l+" or "l-") any (positively or negatively) charged lepton
-
* p2 (D=0): If cut is between pairs of particles, this attribute
+
* ...
-
should be non-zero. Allowed values are the same as for p1
+
* p2 (D=0): If cut is between pairs of particles, this attribute should be non-zero. Allowed values are the same as for ''p1''
* min (D=-inf): The minimum value of this variable
* min (D=-inf): The minimum value of this variable
* max (D=+inf): The maximum value of this variable
* max (D=+inf): The maximum value of this variable

Revision as of 12:38, 10 June 2009

Contents

Introduction

The Les Houches Event File accord (LHEF) was introduced in 2006 and was meant as a standard way of representing in an ASCII file the information in the old Les Houches common block accord from 2001. LHEF was constructed using XML tags to be easy to extend (although some additional structure is assumed inside some tags which is not formulated in XML). The standard has been extremely usefull, and has been used a lot to interface matrix element generators and parton shower programs.

The standards are found here:

As the matching and merging of tree-level matrix elements and parton showers are now becoming the state-of-art, it is reasonable to let this be reflected in an updated file format to standardise how relevant information should be given by the matrix element generators (MEGs) in a usable fashion for the parton shower programs (PSGs). Furthermore, looking ahead towards the time when NLO matching and merging with parton showers hopefully will become the standard, it might be worth thinking about which additional information is needed for the parton showers in this case.

Below you will find a rough draft of additional XML tags suggsted to be included in the new standard (version 2.0).

Run information

This is information about all events in the file to be included inside the "init" tag after the compulsary block of parameters corresponding to the HEPRUP common block.

The xsecinfo tag (required)

The information in the HEPRUP common block is in principle sufficient to figure out the cross sections of the processes involved. However, the way things are specified is a bit confusing and complicated since it was assumed to be used to pass information between the MEG and PSG in both directions. For the event file, the communication is per definition one-way, and the information can be made more easily provided. The suggested attributes for the xsecinfo tag are as follows (R means the attribute is required. 'D=' means a default is assumed if the tag is absent).

  • neve (R): the number of events in the file
  • totxsec (R): the total cross section (in units of pb) of all processes in the file
  • maxweight (D=1): the maximum weight of any event in the file (in an arbitrary unit)
  • meanweight (D=1): The average weight of the events in the file (same unit as maxweight.
  • negweights (D=no): If yes, the file may contain events with negative weights.
  • varweights (D=no): If yes, the file may contain varying weights (if no, all events are weighted with maxweight=meanweight).

The information given per process in the HEPRUP common block can then safely be ignored and the cross section for each process is assumed to be sumprocw*totxsec/maxweight/neve.


The cutsinfo tag (optional)

Here the MEG should supply information about the cuts used in the generation. Inside this tag any number of cut tags can be supplied.

The cut tag

The cut tag has information of a particular cut used. The information needed is which particle(s) are affected, what variable is used and the maximum and/or minimum value of that parameter. The attributes are

  • type (R): This defines the variable which is cut. The following values are allowed (the lab frame is assumed in all cases):
* "invmass" the invariant mass of two particles (or if only one particle type is given, the rest mass of that particle).
* "kt" the transverse momenta of a particle (in GeV)
* "eta" the pseudorapidity of a particle
* "y" the true rapidity of a particle
* "deltaR" the pseudorapidity--azimuthal-angle difference between two particles.
* "E" the energy of a particle
* "ETmiss" the sum of the pt of the neutrinos in the process
* ...
  • p1 (D=any): The particle for which this cut applies. This can either be a number corresponding to a given particle PDG code or one of the following
* "any" any particle
* "jet" any coloured particle
* "uds" ("udsc") any light quark
* "guds" ("gudsc") any light quark or gluon
* "b" ("c") any b or bbar (c or cbar) quark
* "l" ("l+" or "l-") any (positively or negatively) charged lepton
* ...
  • p2 (D=0): If cut is between pairs of particles, this attribute should be non-zero. Allowed values are the same as for p1
  • min (D=-inf): The minimum value of this variable
  • max (D=+inf): The maximum value of this variable
Personal tools